←
Nirav Patel577 posts
Nirav Patel avatar

Nirav Patel

@cmonkey

Founder (and usually tweeting) at @FrameworkPuter

◷ Joined June 2007▧ 51 Photos and videos
Nirav Patel avatar
Nirav Patel@cmonkey·15 Oct 2022

Standing offer: If you’re building consumer hardware and want advice on anything (business strategy, building a team, finding suppliers, go to market, design/architecture decisions, fundraising, etc), send me a DM and I am happy to have a call with you.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 17

A core part of our product philosophy is solving consumer frustrations. This category was frustrating, and I'm proud of our team for solving it!

Pre-orders are open now for Framework Wireless Touchpad Keyboard. Finally, a living room keyboard you want to use.

Post attachmentPost attachmentPost attachment
Nirav Patel avatar
Nirav Patel@cmonkey·Nov 13

On Duo, Apple Books should show the book cover on the outer screen so you can read more performatively.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 11

A better example with these instructions from the start. This looks pretty close to what I would have placed and routed by hand (though it is a simple board).

Post attachment

It doesn't take a lot of instruction to make Fable 5.2's routing look closer to what a human would do (though it still loves right angles in traces).

Post attachment
Nirav Patel avatar
Nirav Patel@cmonkey·Nov 11

- When placing a PCB, place it the way an experienced layout engineer would by hand: - For sub-systems sensitive to placements, like ESD protection, crystals, and passives for switching regulators, follow the layout in the relevant datasheet where possible. - Put each decoupling capacitor directly at the supply pin it serves, with its pad facing the pin and about 1 mm away. Treat a reference design's looser spacing as a maximum, not a target. - Put every other passive at the pin it serves, oriented so the connection is a short straight trace. - Group related parts and align them: shared centre lines, even pitch, rows like capacitor – IC – capacitor, test pads on a grid. - Keep one legible reference label per part, with no overlapping text. - Review a rendered image of the placement before presenting it, not just DRC, and fix anything that looks scattered or misaligned.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 11

In my CLAUDE.md: - When routing a PCB, do it the way an experienced layout engineer would by hand: - No bends sharper than 135°. No square or acute junctions: branch at 45°, and preferably at a pad or via. - Tracks leave pads and vias from the centre, in a straight run until clear of the copper. No hooks or doubling back. - Tracks that run the same way within about 0.5 mm of each other are routed side by side at the clearance rule. Plan buses and nets with a common destination as bundles before routing them. - Leave no gaps that are too narrow to use: either at minimum spacing or wide enough for another track plus clearance. Avoid slivers and pour islands. - Stagger vias so bundled tracks can stay together up to their ends. - Start with power pours, then sensitive buses like high speed differential pairs and the micro routing around crystals and switching regulators, then more general bundles of low speed signals.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 11

It doesn't take a lot of instruction to make Fable 5.2's routing look closer to what a human would do (though it still loves right angles in traces).

Post attachment
Nirav Patel avatar
Nirav Patel@cmonkey·Nov 10

Before anyone jumps on it, this was a first pass with no input from me other than asking it to route it within JLC's default 6 layer design rules. At first glance, it looks like it should function, though I haven't done a review of it yet.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 8

I (well, Opus) just mocked up a quick design of a mostly drop-in replacement for a Raspberry Pi Zero 2 W. It loses the HDMI interface, but otherwise likely handles a lot of the use cases that RPi Zero is used (and overkill) for.

Nirav Patel avatar
Nirav Patel@cmonkey·Nov 8

With DDR and LPDDR shortages and pricing breaking the single board computer category, it's interesting to see that PSRAM-only microcontrollers are getting closer to closing the gap. e.g. ESP32-S31 has a real MMU and can run Linux!

Post attachment
Nirav Patel avatar
Nirav Patel@cmonkey·Oct 17

Controversial restaurant opinion of the week: Sungho is better than San Ho Won and should have the star instead.